Is Port Jackson Wood Good for a Braai? What to Know Before You Burn It

Is Port Jackson Wood Good for a Braai? What to Know Before You Burn It

Short answer: yes, Port Jackson makes a genuinely good braai wood — dense, hard, and happy to sit as long-lasting coals while you cook. But like any wood, it rewards a bit of knowledge. Here is what to know before you light it.

What Port Jackson Actually Is

Port Jackson is the common name for Acacia saligna, an Australian wattle that has spread widely across the Western and Eastern Cape and right through the Garden Route. Because it grows so readily here, it is commonly available as cut wood — often the wood you see stacked at the side of the road or sold by someone who has been clearing a stand of it. That local abundance is part of why it turns up so often in braai wood piles. If you are shopping around, have a look at BraaiWattle for dry seasoned wattle wood.

How It Burns

Port Jackson is a dense, hard wood, and that density is what you want in a braai. It burns down into long-lasting coals that hold heat well — the kind of bed you can cook over steadily rather than chasing flames. The catch is moisture: if the wood is not properly dry, it smokes and spits instead of settling into clean coals. Dry wood is the whole game here.

Telling Port Jackson From Black Wattle

The two wattles are often confused, but a few simple checks help:

  • Bark: look at the texture and colour of the trunk and branches — the two species differ in how the bark sits and splits.
  • Leaf: Port Jackson carries long, narrow, willow-like leaves, which is why it is sometimes called the golden wreath wattle.
  • The split: when you split a piece, notice how the grain runs and how cleanly it separates — the two woods behave differently under the axe.

None of this needs to be scientific. Once you have handled both a few times, the difference becomes obvious.

Why Clearing Wood Makes Sense as Fuel

Port Jackson is invasive, which means it is being removed from land anyway. Burning clearing wood is a sensible fuel choice: you are using something that is coming out regardless, rather than cutting indigenous trees for the fire. That is a quietly practical reason to feel good about a bag of wattle wood.

Seasoning and Storing It

Good braai wood is mostly patience. To season Port Jackson:

  1. Split it — smaller pieces dry faster and more evenly.
  2. Stack it off the ground so air can move underneath.
  3. Cover the top only, leaving the sides open to breathe.
  4. Give it time. Port Jackson needs a decent dry-out before it is at its best.

Rushed wood smokes. Properly dry wood gives you the clean, steady coals you are after.

How Much You Need and How to Build the Fire

For a standard family braai, a modest pile of split wood goes a long way — Port Jackson’s dense coals mean you need less than you might think. Build the fire in stages:

  • Start with kindling — paper, twigs, small dry splits.
  • Add split pieces once the kindling has caught.
  • Once you have a bed of coals, lay bigger logs on top to keep the heat going.

Cook over the coals, not the flames. That is where Port Jackson shines.

Honest Downsides

  • Hard to split when green — it fights back until it has dried a bit.
  • Dry bark can throw sparks, so keep an eye on the fire.
  • It needs a longer dry time than some softer woods.
  • It burns hot — overfill the tray and you will have more heat than you need.

None of these are dealbreakers. They are just things to know.

Where to Get Dry Wattle Wood

If you would rather skip the seasoning wait, BraaiWattle supplies dry seasoned wattle braai wood around Wilderness, George, Knysna and Sedgefield. Pop over to braaiwattle.com and we will sort you out. Happy braaing.

Scroll to Top
Opening hours Mon–Fri 08:30–16:30 · Sat 08:30–13:00 · Closed Sundays
WhatsApp orders any time: 076 559 3725
⭐ Review us on Google